All times are Pacific
Contains new posts in your subscriptions since the last time you logged on.
No new posts in your subscriptions since the last time you logged on.
|Diesel Truck World - Diesel Trucks - When gas will not do - forums, photos and more.||Congratulations Texas Chapter!||
|Performance clutch||CTDYoungGun||10||7/3/2012 5:03p|
|2006 ctd tranny?||dcrenshaw26||5||3/19/2012 9:00p|
|05 auto tranny TSB||BelgianMagic||3||3/9/2012 6:10p|
|what exactly does a performance ignition do?||jhnharvy773||1||7/19/2011 11:13a|
|good looking engine dress up kit?||jhnharvy773||1||7/6/2011 5:48a|
|48RE ( 1 2 )||Fog Runner||21||2/19/2011 10:00a|
|Which clutch for a 6 speed||Jason Rightmire||0||4/22/2008 7:08p|
|Need some feedback||rednekroper05||1||4/6/2008 5:09p|
|Which is better ATS SUNCOAST DTT||04 HO Cummins||4||2/20/2008 3:34a|
|Lock out OD||dpttruck||1||1/3/2008 6:00a|
|Trans Problems||06Cummins||3||7/17/2007 12:52p|
|Down hill assist?||yotd1976||2||6/13/2007 9:06a|
|How hard would it be||4x4cummins04||4||6/7/2007 2:43a|
|Loops loops loops||Twisted Shifter||0||6/2/2007 5:29a|
|What do I need to upgrade?||VTDeezl||0||5/31/2007 5:30a|
|Tips on tranny upgrades?||hnilica20||4||5/24/2007 6:05a|
|Attn. Manual Trannys||pick75||7||5/19/2007 9:10a|
|00 CTD trans?||06 DIESEL||1||4/19/2007 6:07a|
|Welp i think my tranny is starting to go||Cummins4ever||8||3/6/2007 4:50p|
|6 speed swap||rednekroper05||1||2/26/2007 6:59a|
|Whats the best up grade four a 48re? ( 1 2 )||Fullpull3||20||2/10/2007 4:37p|
|Clutch suggestions||rednekroper05||8||2/6/2007 12:35p|
|#5 Race setting on Edge||Northernhunter||5||1/31/2007 11:09a|
|2005 TRANNY?S||Texas Dirt Dog||0||1/30/2007 5:08a|
|Tranny question||rednekroper05||6||1/30/2007 5:04a|
|Transmission rep[lacement||rdrunr123||1||1/29/2007 7:53a|
|Reverse Band gone in 3 days?||pipeguycan||7||1/24/2007 2:58p|
|DIESEL TRANNY BEEFING||CUMMINSSOON||5||1/24/2007 3:10a|
|Limited slip diff conversion||Sweeper||1||1/12/2007 4:45p|
Slowly, the world is recognizing the benefits and value of cost saving and minimalism through DIY jobs and this is the reason why it is important to get proper information about how brake pads can be repaired and replaced at home.
When this is done, a lot of money can be saved. However, when you do it in an improper manner, a lot of cost would have to be paid. Given below are some ways in which the Nissan brake pads or the Porsche brake pads can be replaced and common errors can be avoided.
Are you experiencing shaking or vibrations?
When thereâ€™s warping of brake rotors, the vehicle starts shaking and there are vibrations. When brakes are applied quickly, the car shakes owing to run out. If the rotor is thick enough, you can machine or resurface them so that they work properly. If there is no pulsation or shaking, brake pads can be replaced without any sort of machining. Always keep in mind that in majority of the cases, the machines have to be replaced. Without that, squeaking or irritating noises will be experienced. Ensure that you properly take care of them either by replacing; take proper care while replacing jeep brake pads.
It sounds very elementary but you canâ€™t take the safety factor lightly. To start a car job, learn how it must be lifted safely. This factor is ignored by many people and jack stand isnâ€™t used. Hydraulic jacks are not safe because there is a risk of failing or slipping. When jackstand is used it offers safety; even if the car will fail, there will be something at least to support. Jack stand can be used for routine jobs and these include oil changes, starter replacement, brake pads replacement etc.
When the jack fails, the person who is under it might be crushed. Such accidents are reported many a times when car owners and technicians are crushed when they change starter or do a similar job or repairs.
Slow leak might result in the lowering of car all of a sudden. If a person is pinned, itâ€™s difficult to get out of it without seeking help from outside. However, the ability of shouting is limited because the chest is stuck. It can also cost life.
How to remove rotors, wheels and calipers?
Firstly, the wheels have to be removed and then the tools that are needed should be determined. This can be done easily by finding bolts and checking the kind of head.
There are 3 kinds of bolt heads i.e. allen, torx and regular. All systems have caliper bracket and caliper and 2 bolts hold them. If the brake pads have to be replaced, the caliper has to be removed. Ensure that the brake hose is safe. Elastic cord can be used for suspending the caliper.
Caliper bracket has to be removed for replacement or machining of rotor.
For more info visit here :- Performance Brake Drums
Posted by: BrakeWorld
|License plate on tra...||Dodge: Towing|
|Which is a better In...||Dodge: Intake System|
|How many mechanics d...||Chat Room|
|Trucks & Guns||General Discussions|
|So....DTW is back!!!||Chat Room|
|How many miles to yo...||General Discussions|
|Jacobs Exhaust Brake?||General Discussions|
|New to This site||Community|
|What tire size will...||Other: Wheels and Tires|
|Performance clutch||Dodge: Transmission|